SEAL Image 600-C Anleitung zur Fehlerbehebung

Image® 600-C Laminator Image® 600-C Laminator Owner’s Operation Manual

10LAMINATOR FEATURES Figure 3. Laminator Features 1. Control panel system • For independent control of pressure, roller activat

11 6 O O-C102345678910(Reset Up)Reset Power After Emergency Stop020406080100120140160FRONT CONTROL PANEL 1. Air Regulator Knob: Adjusts the downwa

12CHECKING OPERATION After you are familiar with the control panel and its functions, check all operations. CHECK THE MAIN POWER • Press the main

13SET-UP AND OPERATION HOW TO SET THE SHIM WHEELS • First, determine the thickness of the board that you will use for mounting. • You must first r

14SET-UP AND OPERATION SETTING THE UNWIND BRAKE TENSION IMPORTANT! The brake tension greatly affects the smooth flow of the laminating film. • Turn

15SET-UP AND OPERATION AUTO-RUN OPERATION • The continuous-run operation allows the user to start the roller rotation and adjust the roller speed b

16FEEDING IMAGES BASIC STEPS TO FEEDING IMAGES NOTE: For good results, the process requires that the images be fed through correctly. • Make sure

17WEBBING FILMS WITH A RELEASE LINER (NORTH AMERICA) The following are the basic webbing procedures for webbing films with a release liner. It is im

18WEBBING FILMS WITH A RELEASE LINER (EUROPE & ASIA)The following are the basic webbing procedures for webbing films with a release liner: It is

19DECALING (PRESSURE- SENSITIVE) This process involves applying a cold pressure-sensitive over-laminate to the top and a cold pressure-sensitive mou

2TABLE OF CONTENTS TABLE OF CONTENTS...

20MOUNTING This process involves mounting previously prepared decals onto a substrate. No films or adhesives are required for this process. TO MOUN

21PRE-COATING BOARDS This process is used to coat substrates with a self-adhesive coating onto which images can be mounted. Images can then be mount

22APPLYING AN OVER-LAMINATE An Over-laminate with a release liner can be applied to your mounted prints, photographs or images on photographic paper

23GLOSSARY OF TERMS DECAL: An image that has been laminated with a pressure-sensitive film on top and with an adhesive backing. FILM: A synonym for

24PROCESS APPLICATION NOTES _______________________________________ _______________________________________ _____________________________________

25PROCESS CONTROL SHEET Process: __________________________________ Application Use: ____________________________ Top Unwind: _____________________

26CLEANING / MAINTAINING YOUR LAMINATOR CLEANING THE LAMINATOR • The laminator may be cleaned with a lint-free cloth, lightly dampened with a mild

27PERIODIC MAINTENANCE SHEET GREASE BEARINGS CHAIN TENSION ADJUSTMENT / OIL CHAIN ** DRAIN WATER (AIR FILTER)*** SAFETY CHECK AFTER SERVICING

28TROUBLESHOOTING GUIDE Problem Solution The laminator will not turn on. • Check if the power cable is plugged into the mains wall outlet. • Che

29SPARE PARTS LIST Please contact Technical Service for replacement parts. PART DESCRIPTION PART # Air Compressor 225020 Air Cylinder Kit 6008

3INTRODUCTION Thank you for purchasing a SEAL® Image® 600-C Laminator. We have designed the SEAL Image 600-C to give you years of reliable service. A

30TECHNICAL SPECIFICATIONS MECHANICAL Dimensions (H x W x D) 78”w x 32”d x 50”h (198 cm x 81 cm x 127 cm) Net Weight 630 lbs. (286 kg) Shipping We

31LIMITED WARRANTY SEAL® Graphics warrants to the original consumer purchaser that each new SEAL® Image® Laminator, which proves defective in mater

32 SEAL BRANDS TECHNICAL SERVICE SEAL BRANDS TECHNICAL SERVICE – EUROPE AND ASIA PACIFIC (For technical assistance & service) (For

4WORKSPACE / ELECTRICAL REQUIREMENTS • Keep the area around your laminator clear with adequate space around it so you can feed, receive and trim mo

5ENVIRONMENT CONDITIONS The following environmental conditions are ideal for the best operation of the laminator. AMBIENT TEMPERATURE The best temp

6UNPACKING, SET-UP AND INSTALLATIONONLY SKILLED PERSONNEL SHOULD PERFORM INSTALLATION. READ AND COMPLY WITH ALL WARNINGS AND FOLLOW THE PROPER INSTA

7UNPACKING, SET-UP AND INSTALLATIONUNPACKING YOUR LAMINATOR • Remove the transport packing and the plastic shrink-wrap the laminator is wrapped in

8IMPORTANT SAFEGUARDS SAFETY SYMBOLS USED ON THE LAMINATOR IMPORTANT! Read and make sure you understand these safety and operating guidelines. ROTA

9SAFETY FEATURES The SEAL® Image® 600-C Laminator is designed with safety and protective devices with the user’s safety of utmost consideration. How